Preliminary msmac3D V2.30 Update

General Questions, answers and information related to the release of the msmac3D program.
Post Reply
MSI
Site Admin
Posts: 1264
Joined: Thu Jun 18, 2009 12:37 pm

Preliminary msmac3D V2.30 Update

Post by MSI » Mon Jan 15, 2018 2:40 pm

msmac3D v2.30 Preliminary update now posted up.
  • All users should have received an email. if you did not please check your SPAM folder or simply let us know and we will forward the email to you.
This is an update to v2.22 and NOT a full installation. It is also an unsigned update so your computer might complain 'unknown application' however know that it is from McHenry Software and is a legitimate preliminary update. Once we do some additional testing we will digitally sign the official update.
  • We are sending this out for users who would like the latest version
    • If you run into any issues please let us know
    • If need to, use Program and Features ->Uninstall McHenry msmac3D Graphics3D
    • And then simply reinstall v2.22.
  • Here is a quick list of some of the new features in this update
    • DXF Mesh surface import
    • Google Elevation data can now be imported
    • Friction Zone improvements
    • New Movie creation abilities both in setting sizes and wmv movie creations.
    • Ability to start in msmac3D graphics directly or in the medit3D gird
2018 Training: Be sure to sign up for training this week. Each session will be approximately 1 hour. We will cover general introduction topics and any topics per your requests. Please include areas you'd like covered in your emails. You can attend ANY and ALL that you'd like:
  • Training#7: Tuesday January 16 at 11:00 AM EST
  • Training#8: Thursday January 18 at 01:30 PM EST
  • email or Call our offices and let us know which session(s) you will attend.
Question? Comment? Please email forum@mchenrysoftware.com. Also see the McHenry Forum Index
Visit McHenrySoftware.com for technical information & software.
(c) McHenry Software, Inc ALL Rights Reserved.

MSI
Site Admin
Posts: 1264
Joined: Thu Jun 18, 2009 12:37 pm

Re: Preliminary msmac3D V2.30 Update

Post by MSI » Wed Jan 17, 2018 9:54 am

Couple issues encountered in the Preliminary update:
  • Please be sure your antivirus is disabled so it allows the program to fully install. Some anti virus (Microsoft) have quarantined some components without notification if not disabled during installation which causes program to not function properly
    • All components not digitally signed in Prelim release, will be in official release
  • FIXED Jan 17, 2018 230 PM EST! Running msmac3D in 2D we have found causes the program to hang. We expect to have a resolution to that issue later today (Wed Jan 17th). The issue is related to the new cancel command we have for 3D simulations since with very large point clouds sometimes the simulation can run for a long time and we wanted to allow the ability to cancel. That apparently has created an issue with running msmac3D in 2D mode since it runs almost instantaneously. We expect a resolution shortly.
Please let us know if you have any problems or issues with the preliminary release.
The official release of Version 2.30 is expect in the next week or so.

Thank you for your support of McHenry Software!
Question? Comment? Please email forum@mchenrysoftware.com. Also see the McHenry Forum Index
Visit McHenrySoftware.com for technical information & software.
(c) McHenry Software, Inc ALL Rights Reserved.

MSI
Site Admin
Posts: 1264
Joined: Thu Jun 18, 2009 12:37 pm

Re: Preliminary msmac3D V2.30 Update

Post by MSI » Wed Jan 17, 2018 2:39 pm

Jan 17, 2018: 230 PM EST: Issue withmsmac3D running in 2D mode corrected in preliminary update.
Question? Comment? Please email forum@mchenrysoftware.com. Also see the McHenry Forum Index
Visit McHenrySoftware.com for technical information & software.
(c) McHenry Software, Inc ALL Rights Reserved.

Post Reply